ARM Musca-S1 Technical Reference Manual Download Page 107

Page: 107 / 194

3.7

Real Time Clock

The Musca

‑

S1 test chip implements an Arm PrimeCell Real Time Clock.

The base memory addresses of the

Real Time Clock

(RTC) control registers are:

• 0x4010_8000 in the Non-secure region.
• 0x5010_8000 in the Secure region.

See the

Arm

PrimeCell Real Time Clock (PL031) Technical Reference Manual

Caution

Warm reset of the Musca

‑

S1 test chip resets the Real Time Clock.

The following table shows the Real Time Clock registers in the Musca

‑

S1 test chip in address offset

order from the base memory address. Undefined registers are reserved. Software must not attempt to
access these registers.

Table 3-42 Real Time Clock control registers summary

Offset

Name

Type Reset

Width Function

0x0000

RTCDR

0x0000_0000

Data register.

0x0004

RTCMR

0x0000_0000

Match register.

0x0008

RTCLR

0x0000_0000

Load register.

0x000C

RTCCR

0x0000_0000

Control register.

0x0010

RTCIMSC

0x0000_0000

Interrupt mask set and clear register.

0x0014

RTCRIS

0x0000_0000

Raw interrupt status register.

0x0018

RTCMIS

0x0000_0000

Masked interrupt status register.

0x001C

RTCICR

0x0000_0000

Interrupt clear register.

0x0FE0

RTCPeriphID0 RO

0x0000_0031

Peripheral ID register bits [7:0]

0x0FE4

RTCPeriphID1 RO

0x0000_0010

Peripheral ID register bits [15:8]

0x0FE8

RTCPeriphID2 RO

0x0000_0004

Peripheral ID register bits [23:16]

0x0FEC

RTCPeriphID3 RO

0x0000_0000

Peripheral ID register bits [31:24]

0x0FF0

RTCPCellID0

0x0000_000D

PrimeCell ID register bits [7:0]

0x0FF4

RTCPCellID1

0x0000_00F0

PrimeCell ID register bits [15:8]

0x0FF8

RTCPCellID2

0x0000_0005

PrimeCell ID register bits [23:16]

0x0FFC

RTCPCellID3

0x0000_00B1

PrimeCell ID register bits [31:24]

3 Programmers model

3.7 Real Time Clock

101835_0000_01_en

reserved.

3-107

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands