ARM Musca-S1 Technical Reference Manual Download Page 30

Page: 30 / 194

Table 2-2 Clock control SCC registers

Register

Register function

Register description

CLK_CTRL_SEL

Controls the following blocks:
•

PREMUX

•

DAPSWMUX

•

MAINMUX

•

REFMUX

•

SCCMUX

•

RM38KMUX

•

TESTMUX

CLK_CTRL_SEL Register

on page 3-128

CLK_PLL_PREDIV_CTRL

Controls PREDIV.

CLK_PLL_PREDIV_CTRL Register

on page 3-130

CLK_BBGEN_DIV_CLK

Controls BBGENDIV

CLK_BBGEN_DIV_CLK Register

on page 3-131

CLK_POSTDIV_CTRL_QSPI Controls QSPIDIV.

CLK_POSTDIV_CTRL_QSPI Register

on page 3-131

CLK_POSTDIV_CTRL_RTC

Controls RTCDIV.

CLK_POSTDIV_CTRL_RTC Register

on page 3-132

CLK_POSTDIV_CTRL_TEST Controls TESTDIV.

CLK_POSTDIV_CTRL_TEST Register

on page 3-132

CTRL_BYPASS_DIV

Controls the clock divider bypass functions.

CTRL_BYPASS_DIV Register

on page 3-133

CLK_CTRL_ENABLE

Enables

Clock Gates

(CGs).

CLK_CTRL_ENABLE Register

on page 3-135

SCC_MRAM_CTRL0

Enables eMRAM clock CG.

SCC_MRAM_CTRL0 Register

on page 3-160

SCC_MRAM_CTRL1

Controls eMRAM_DIV

SCC_MRAM_CTRL2 Register

on page 3-163

The FCLK_DIV and SYSCLK_DIV system control registers control the FCLKDIV and SYSCLKDIV
dividers in the SSE-200 subsystem. FCLKDIV derives clock

FCLK

for secondary processor CPU1 and

SYSCLKDIV derives

SYSCLK

for primary processor CPU0.

The following table shows system control registers FCLK_DIV and SYSCLK_DIV.

Table 2-3 System control registers FCLK_DIV and SYSCLK_DIV

Register

Register function

Register description

FCLK_DIV

Controls divider block FCLKDIV in SSE-200 subsystem to derive clock

FCLK

for secondary processor CPU1.

FCLK_DIV Register

on page 3-100

SYSCLK_DIV Controls divider block SYSCLKDIV in SSE-200 subsystem to derive clock

SYSCLK

for primary processor CPU0.

SYSCLK_DIV Register

on page 3-101

Multiplexed I/O

The

DAPSCCCLK

signal is present on Musca

‑

S1 test chip I/O PA24 which is part of the multiplexed

Musca

‑

S1 test chip I/O. The IOMUX registers control the multiplexed Musca

‑

S1 test chip I/O.

Note

The

DAPSCCCLK

input is reserved. In normal operation, software must not change

PRE_MUX_CLK

as the input to multiplexer SCCMUX. See

CLK_CTRL_SEL Register

on page 3-128

TEST_CLK

is present on Musca

‑

S1 test chip I/O PA13 which is also part of the multiplexed Musca

‑

test chip I/O. The IOMUX registers select

TEST_CLK

by selecting alternative function ALTF2 for

Musca

‑

S1 test chip I/O PA13.

2 Hardware description

2.5 Clocks

101835_0000_01_en

reserved.

2-30

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands