ARM Musca-S1 Technical Reference Manual Download Page 100

Page: 100 / 194

Table 3-32 System Control Registers summary (continued)

Offset

Name

Access Reset value

Description

0x0214

PDCM_PD_SRAM2_SENSE RW

0x0000_0000

Power Control Dependency Matrix.

PD_SRAM2 power domain sensitivity.

0x0218

PDCM_PD_SRAM3_SENSE RW

0x0000_0000

Power Control Dependency Matrix.

PD_SRAM3 power domain sensitivity.

0x0FD0

PIDR4

0x0000_0004

Peripheral ID4

0x0FE0

PIDR0

0x0000_0054

Peripheral ID0

0x0FE4

PIDR1

0x0000_00B8

Peripheral ID1

0x0FE8

PIDR2

0x0000_000B

Peripheral ID2

0x0FEC

PIDR3

0x0000_0000

Peripheral ID3

0x0FF0

CIDR0

0x0000_000D

Component ID0

0x0FF4

CIDR1

0x0000_00FO

Component ID1

0x0FF8

CIDR2

0x0000_0005

Component ID2

0x0FFC

CIDR3

0x0000_00B1

Component ID3

FCLK_DIV Register

The FCLK_DIV Register characteristics are:

Purpose

Controls the divider value of clock divider FCLKDIV that derives

FCLK

, in the SSE-200

subsystem, from

MAINCLK

in the Musca

‑

S1 test chip.

FCLK

drives the secondary processor

element, CPU1.

Usage constraints

Bits[20:16] are read-only. Bits[4:0] are read/write. The other bits are reserved.

Memory offset and full register reset value

See

3.5.3 System Control Register Block

on page 3-99

The following table shows the bit assignments.

Table 3-33 FCLK_DIV Register bit assignments

Bits

Name

Function

[31:21] -

Reserved.

[20:16] FCLKDIV_CUR

Current value of FCLKDIV:

The division value of FCLKDIV divider is
FCLK1.

These bits are read-only.

Reset value

0b00000

3 Programmers model

3.5 System control element

101835_0000_01_en

reserved.

3-100

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands