ARM Musca-S1 Technical Reference Manual Download Page 59 | Manualshive

Page: 59 / 194

background image

Interrupt controller registers

The following table shows the Musca

‑

S1 test chip interrupt controller registers. Undefined registers are

reserved. Software must not attempt to access these registers.

Table 3-5 Summary of interrupt controller registers

Address

Name

Type Reset value

Description

0xE000E004

ICTR

RO

-

Interrupt Controller Type Register

0xE000_E100

-

0xE000_E11C

NVIC_ISER0-NVIC_ISER7

RW

0x0000_0000

Interrupt Set Enable Registers

0xE000_E180

-

0xE000_E19C

NVIC_ICER0-NVIC_ICER7 RW

0x0000_0000

Interrupt Clear Enable Registers

0xE000_E200

-

0xE000_E21C

NVIC_ISPR0-NVIC_ISPR7

RW

0x0000_0000

Interrupt Set Pending Registers

0xE000_E280

-

0xE000_E29C

NVIC_ICPR0-NVIC_ICPR7 RW

0x0000_0000

Interrupt Clear Pending Registers

0xE000_E300

-

0xE000_E31C

NVIC_IABR0-NVIC_IABR7 RO

0x0000_0000

Interrupt Active Bit Registers

0xE000_E400

-

0xE000_E41F

NVIC_IPRO-NVIC_IPR7

RW

0x0000_0000

Interrupt Priority Registers

See the following documents for more information on the interrupt controller:
•

Arm

®

Cortex

®

‑

M33 Processor Technical Reference Manual (r0p2)

.

•

Arm

®

v7

‑

M Architecture Reference Manual

.

Processor core Interrupt Registers

The SSE-200 block implements CPU0 and CPU1 core Interrupt Registers. The Interrupt Registers enable
software to raise interrupts, clear interrupts, and check the written value that raises the interrupts to the
cores.

Set and Clear registers support setting and clearing of individual bits which means the individual bits can
represent events that can be independently set and cleared.

The CPU0 and CPU1 Interrupt Registers are:

• CPU0INTR_STAT - Core 0 Interrupt Status Register.
• CPU0INTR_SET - Core 0 Interrupt Set Register.
• CPU0INTR_CLR - Core 0 Interrupt Clear Register.
• CPU1INTR_STAT - Core 1 Interrupt Status Register.
• CPU1INTR_SET - Core 1 Interrupt Set Register.
• CPU1INTR_CLR - Core 1 Interrupt Clear Register.

See the following for more information on the CPU0 and CPU1 Interrupt Registers.
•

3.4.8 Message Handling Unit

.

•

Arm

®

CoreLink

™

SSE

‑

200 Subsystem for Embedded Technical Reference Manual (r1p0)

.

Wakeup Interrupt Controller (WIC)

The WIC is a peripheral that detects an interrupt signal and wakes the processor from deep

‑

sleep mode.

The WIC is active only when the system is in deep

‑

sleep mode.

The WIC is not programmable and does not have registers or a user interface. It operates entirely under
the control of hardware signals.

When the WIC is enabled and the processor is in deep

‑

sleep mode, the

Power Management Unit

(PMU)

can power down most of the processor. When the WIC receives an interrupt, it takes several clock cycles

3 Programmers model

3.3 Processor elements

101835_0000_01_en

Copyright © 2019, 2020 Arm Limited or its affiliates. All rights

reserved.

3-59

Non-Confidential

«
...
57
58
59
60
61
...
»

Summary of Contents for Musca-S1



































































































































































































Reviews:

No comments

Related manuals for Musca-S1

Brand: York Fitness Pages: 34

Brand: Nemco Pages: 13

Brand: Ecco Pages: 12

Brand: UMF Medical Pages: 12

Brand: Backyard Discovery Pages: 79

Brand: Badger Meter Pages: 16

Brand: Cadman Pages: 84

Brand: Haag-Streit Pages: 16

Brand: Maeda Pages: 276

ST70 Instrument

Brand: Raymarine Pages: 12

Brand: Raven Pages: 73

Brand: Tascam Pages: 3

Brand: RAB Lighting Pages: 4

Brand: campgo Pages: 33

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

i-limb access hand

Brand: Össur Pages: 246

PROPRIO FOOT PSX01

Brand: Össur Pages: 374

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands