ARM Musca-S1 Technical Reference Manual Download Page 54

Page: 54 / 194

3.3

Processor elements

The SSE-200 subsystem in the Musca

‑

S1 test chip implements two processor elements. Each element

contains a Cortex

‑

M33 (r0p2) core.

Processor 0, CPU0, is the main processor. It has FPU and DSP, and no coprocessor. The operating
frequency is 50MHz.

Processor 1, CPU1, is the secondary processor. It has FPU and DSP, and no coprocessor. The operating
clock frequency is 200MHz.

This section contains the following subsections:
•

3.3.1 Private processor regions

on page 3-54

•

3.3.2 Instruction cache configuration interface registers

on page 3-54

•

3.3.3 Processor cache programming

on page 3-55

•

3.3.4 Ensuring the cache handles memory modifications

on page 3-56

•

3.3.5 Interrupts

on page 3-56

3.3.1

Private processor regions

Both processor elements in the system implement a private memory region that only it can see.

The base memory addresses of the private processor regions are:
•

0x4001_0000

in the Non

‑

secure region.

•

0x5001_0000

in the Secure region.

See the

Arm

CoreLink

™

SSE

‑

200 Subsystem for Embedded Technical Reference Manual (r1p0)

for more

information on the private processor regions.

3.3.2

Instruction cache configuration interface registers

The following table shows the instruction cache configuration interface registers. Undefined registers are
reserved. Software must not attempt to access these registers.

Table 3-2 Instruction cache configuration interface registers

Offset

Name

Type Reset

Width Description

0x0000

ICHWPARAMS

0x0000_0000

Hardware Parameter Register

0x0004

ICCTRL

0x0000_0000

Instruction cache Control Register

0x0100

ICIRQSTAT

0x0000_0000

Interrupt Request Status Register

0x0104

ICHRQSCLR

0x0000_0000

Interrupt Status Clear Register

0x0108

ICIRQEN

0x0000_0000

Interrupt Enable Register

0x010C

ICDBGFILLERR RO

0x0000_0000

Debug Fill Error Register

0x0300

ICSHR

0x0000_0000

Instruction cache Statistic Hit Register

0x0304

ICSMR

0x0000_0000

Instruction cache Statistic Miscount Register

0x0308

ICSUC

0x0000_0000

Instruction cache Statistic Uncached Count Register

0x0FD0

PIDR4

0x0000_0004

Product ID Register 4

0x0FE4

PIDR1

0x0000_00B8

Product ID Register 1

3 Programmers model

3.3 Processor elements

101835_0000_01_en

reserved.

3-54

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands