ARM Musca-S1 Technical Reference Manual Download Page 137

Page: 137 / 194

Table 3-76 CLK_CTRL_ENABLE Register bit assignment (continued)

Bits

Name

Function

[1]

CTRL_ENABLE_DAPSWCLK

Enable DAPSWCLK clock gate:

0b0

: Not enabled.

0b1

: Enabled.

Reset value

0b1

[0]

CTRL_ENABLE_1HZ

Enable RTC clock gate:

0b0

: Not enabled.

0b1

: Enabled.

Reset value

0b1

CLK_STATUS Register

The CLK_STATUS Register characteristics are:

Purpose

Stores PLL status values.

Usage constraints

This register is read-only.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the CLK_STATUS Register bit assignments.

Table 3-77 CLK_STATUS Register bit assignment

Bits

Name

Function

[31:2]

Reserved.

[1]

STATUS_LOCK_SIGNAL_PLL0_CLK

PLL lock status:

0b0

: Not locked.

0b1

: Locked.

Reset value

0b1

[0]

STATUS_OUT_CLK_MAINCLK_READY

Main clock ready status:

0b0

: Not ready.

0b1

: Ready.

Reset value

0b1

RESET_CTRL Register

The RESET_CTRL Register characteristics are:

Purpose

Resets Musca

‑

S1 test chip peripherals.

Usage constraints

There are no usage constraints.

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-137

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands