ARM Musca-S1 Technical Reference Manual Download Page 75

Page: 75 / 194

Usage constraints

This register is write-only.

Memory offset and full register reset value

See

3.4.6 Secure Privilege Control Block

on page 3-66

The following table shows the bit assignments of the BRGINTCLR Register.

Table 3-15 BRGINTCLR Register bit assignments

Bits

Name

Function

[31:1]

Reserved.

[0]

BRG_CPU1SYS_CLR

Clear interrupt of write buffer bridge error for
bridge between CPU1 and the system.

0b0

: No effect.

0b1

: Clear interrupt.

Reset value

0b0

BRGINTEN Register

The Bridge Buffer Error Interrupt Enable Register characteristics are:

Purpose

Enables or disables the interrupt of the write buffer bridge error for bridge between CPU1 and
the system.

See the

Arm

CoreLink

™

SSE

‑

200 Subsystem for Embedded Technical Reference Manual (r1p0)

for more information.

Usage constraints

This register is write-only.

Memory offset and full register reset value

See

3.4.6 Secure Privilege Control Block

on page 3-66

The following table shows the bit assignments of the BRGINTEN Register.

Table 3-16 BRGINTEN Register bit assignments

Bits

Name

Function

[31:1]

Reserved.

[0]

BRG_CPU1SYS_EN

Enable or disable the interrupt of the write
buffer bridge error for the bridge between
CPU1 and the system.

0b0

: Disable (mask) interrupt.

0b1

: Enable interrupt.

Reset value

0b0

AHBNSPPCEXP0 Register

The Expansion 0 Non-secure Access AHB slave Peripheral Protection Control Register characteristics
are:

3 Programmers model

3.4 Base element

101835_0000_01_en

reserved.

3-75

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands