ARM Musca-S1 Technical Reference Manual Download Page 108

Page: 108 / 194

3.8

General-purpose timer

The Musca

‑

S1 test chip implements a general

‑

purpose timer (GPT) in the

32K

domain.

The base memory addresses of the general

‑

purpose timer control registers are:

•

0x4010_C000

in the Non

‑

secure region.

•

0x5010_C000

in the Secure region.

The following table shows the general

‑

purpose timer registers in address offset order from the base

memory address. Undefined registers are reserved. Software must not attempt to access these registers.

Table 3-43 General-purpose timer control registers summary

Offset

Name

Type Reset

Width Function

0x0000

GPTRESET

0x0000_0000

Reset Control Register.

See

3.8.1 GPTRESET Register

on page 3-108

0x0004

GPTINTM

0x0000_0000

Masked interrupt status register.

See

3.8.2 GPTINTM Register

on page 3-109

0x0008

GPTINTC

0x0000_0000

Interrupt clear register.

See

3.8.3 GPTINTC Register

on page 3-109

0x0010

GPTALARM0

0x0000_0000

ALARM0 data value register.

See

3.8.4 GPTALARM0 Register

on page 3-110

0x0014

GPTALARM1

0x0000_0000

ALARM1 data value register.

See

3.8.5 GPTALARM1 Register

on page 3-110

0x0018

GPTINTR

0x0000_0000

Raw interrupt status register.

See

3.8.6 GPTINTR Register

on page 3-111

0x001C

GPTCOUNTER RO

0x0000_0000

Counter data value register.

See

3.8.7 GPTCOUNTER Register

on page 3-111

This section contains the following subsections:
•

3.8.1 GPTRESET Register

on page 3-108

•

3.8.2 GPTINTM Register

on page 3-109

•

3.8.3 GPTINTC Register

on page 3-109

•

3.8.4 GPTALARM0 Register

on page 3-110

•

3.8.5 GPTALARM1 Register

on page 3-110

•

3.8.6 GPTINTR Register

on page 3-111

•

3.8.7 GPTCOUNTER Register

on page 3-111

3.8.1

GPTRESET Register

The GPTRESET Register characteristics are:

Purpose

• A write resets the general

‑

purpose timer counter to 1.

• A read returns the current value of the general

‑

purpose timer counter.

Usage constraints

There are no usage constraints.

3 Programmers model

3.8 General-purpose timer

101835_0000_01_en

reserved.

3-108

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands