ARM Musca-S1 Technical Reference Manual Download Page 23 | Manualshive

Page: 23 / 194

background image

Musca

‑

S1 test chip outside the SSE-200 subsystem

• Two 1MB eMRAM memories.
• 2MB Code SRAM: 4 × 512KB independently power

‑

enabled.

• One

Real Time Clock

(RTC) in the Always ON domain.

• One 32-bit general

‑

purpose timer running at 32.768kHz with programmable interrupts.

• 16 external GPIO interrupts.
• 16 GPIO.
• Three

Process, Voltage, and Temperature

(PVT) sensors:

— 501-stage ring oscillators. Software can read data from the sensors in the sensor

peripheral and group registers.

• Three-channel I

2

S:

— Two master transmitters.
— One master receiver.

• Three independent

Pulse Width Modulation

(PWM) outputs.

• Two UARTs, UART0 and UART1. The default connectivity is:

— UART0 to Shield header.
— UART1 to DAPLink. No hardware flow control.

• Two I

2

C, I

2

C0 and I

2

C1, which can be used as master (default), or slave:

• One SPI interface which can be used as master (default), or slave.
• One alternate function I/O multiplexer.
• One QSPI for external flash control with

Execute in Place

(XIP) capability.

• Programmable boot select:

— Internal Code eMRAM.
— External QSPI Flash.

• External powerup reset.
• Three system clock sources:

— External

REFCLK

, 32.768kHz.

— External

FASTCLK

, 32MHz.

— On-chip PLL. Output up to 200MHz.

• One JTAG/SWD debug port.
• One

Serial Configuration Controller

(SCC) with dual access port:

— SCC serial during reset, accessible by DAPLink only while chip is under powerup reset.
— APB after reset, accessible by software, or DAPLink while in debug mode (after reset is

released).

2.2.2

Test chip multiplexed I/O

The Musca

‑

S1 test chip contains interfaces that are multiplexed onto the Musca

‑

S1 test chip I/O. The

IOMUX registers control the GPIO multiplexer that selects the functions that appear at the Musca

‑

S1 test

chip I/O.

The IOMUX registers are part of the

Serial Configuration Control

(SCC) registers that select the ALTF1

or ALTF2 alternative I/O functions.

3.11.1 IOMUX registers

for information on the Musca

‑

S1 test chip I/O multiplexer

and the IOMUX registers.

Note

The IOMUX registers select each Musca

‑

S1 test chip I/O individually.

2 Hardware description

2.2 Musca-S1 test chip

101835_0000_01_en

Copyright © 2019, 2020 Arm Limited or its affiliates. All rights

reserved.

2-23

Non-Confidential

«
...
21
22
23
24
25
...
»

Summary of Contents for Musca-S1



































































































































































































Reviews:

No comments

Related manuals for Musca-S1

Brand: Fein Pages: 248

Brand: ZF Pages: 30

Brand: Raymarine Pages: 111

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: XDP Recreation Pages: 40

Brand: Jaga Pages: 32

Brand: Nel-Tech Labs Pages: 8

Brand: Tactile Medical Pages: 23

Brand: Taarup Pages: 72

Brand: YASKAWA Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands