ARM Musca-S1 Technical Reference Manual Download Page 164

Page: 164 / 194

Table 3-109 SCC_MRAM_CTRL2 Register bit assignments

Bits

Name

Function

[31:16] TIME_TO_STOP

If autostop is enabled, number of
microseconds to wait in inactive mode before
going to STOP mode.

Reset value

0xFFFF

[15:8]

MRAM_CLK_DIV

eMRAM clock divider:

0x00

: No division (bypass).

0x01

: Divide by two (default).

0x10

: Divide by three.

0x11

: Divide by four.

Undefined values are not used.

Reset value

0x01

[7:0]

PRESCALE

Clock prescaler to generate the timebase for
the eMRAM clock. The value of PRESCALE
must always meet the following equality:

PRESCALE=eMRAM clock(MHz).

Preserving this equality generates a 1μS
timebase and ensures correct operation of the
eMRAM memory and clock.

If you adjust the eMRAM clock, you must
adjust PRESCALE to preserve the equality.
For example, if:
•

eMRAM clock =15MHz:
— PRESCALE=

0x0F

(15).

•

eMRAM clock =20MHz:
— PRESCALE=

0x14

(20).

•

eMRAM clock =30MHz:
— PRESCALE=

0x1E

(30).

Reset value

0x19

(25MHz).

SCC_MRAM_DIN0 Register

The SCC_MRAM_DIN0 Register characteristics are:

Purpose

eMRAM data input[31:0].

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the SCC_MRAM_DIN0 Register bit assignments.

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-164

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands