Analog Devices ADuCM320 Hardware Reference Manual Download Page 2

Page: 2 / 196

UG-498

ADuCM320 Hardware Reference Manual

Rev. C | Page 2 of 196

TABLE OF CONTENTS

Scope .................................................................................................. 1

Disclaimer .......................................................................................... 1

Functional Block Diagram .............................................................. 1

Revision History ............................................................................... 4

Using the ADuCM320 Hardware Reference Manual .................. 6

Number Notations ........................................................................ 6

Acronyms and Abbreviations ..................................................... 6

Introduction to the ADuCM320 .................................................... 7

Main Features of ADuCM320 .................................................... 7

Memory Organization ................................................................. 8

Clocking Architecture .................................................................... 10

Clocking Architecture Features ................................................ 10

Clocking Architecture Block Diagram .................................... 11

Clocking Architecture Overview.............................................. 12

Clocking Architecture Operation ............................................ 12

Power Management Unit ............................................................... 16

Power Management Unit Features ........................................... 16

Power Management Unit Overview ......................................... 16

Power Management Unit Operation ........................................ 16

Code Examples ........................................................................... 17

ARM Cortex-M3 Processor .......................................................... 19

ARM Cortex-M3 Processor Features ....................................... 19

ARM Cortex-M3 Processor Overview .................................... 19

ARM Cortex-M3 Processor Operation ................................... 19

ARM Cortex-M3 Processor Related Documents ................... 20

ADC Circuit .................................................................................... 21

ADC Circuit Features ................................................................ 21

ADC Circuit Block Diagram ..................................................... 21

ADC Circuit Overview .............................................................. 22

ADC Circuit Operation ............................................................. 22

ADC Transfer Function ............................................................. 23

ADC Typical Setup Sequence ................................................... 24

ADC Input Buffer ....................................................................... 24

ADC Internal Channels ............................................................. 24

ADC Support Circuits ............................................................... 25

Analog Comparator ....................................................................... 35

Analog Comparator Features .................................................... 35

Analog Comparator Overview ................................................. 35

Analog Comparator Operation ................................................ 35

IDACs ............................................................................................... 37

IDAC Features ............................................................................ 37

IDAC Block Diagram ................................................................. 37

IDAC Overview .......................................................................... 37

VDACs ............................................................................................. 43

VDAC Features ........................................................................... 43

VDAC Block Diagram ............................................................... 43

VDAC Overview ........................................................................ 43

VDAC Operation ....................................................................... 43

System Exceptions and Peripheral Interrupts............................. 49

Cortex-M3 and Fault Management ......................................... 49

External Interrupt Configuration ............................................ 53

Low Voltage Analog Die Interrupt Configuration................. 56

Reset ................................................................................................. 59

Reset Features ............................................................................. 59

Reset Operation .......................................................................... 59

DMA Controller ............................................................................. 61

DMA Features ............................................................................. 61

DMA Overview .......................................................................... 61

DMA Operation ......................................................................... 61

Summary of Contents for ADuCM320





































































































































































































Search results

Summary of Contents for ADuCM320

Reviews:

Related manuals for ADuCM320

Brands by name

Popular brands

Analog Devices ADuCM320, Hardware Reference Manual

Search results

Summary of Contents for ADuCM320

Reviews:

Related manuals for ADuCM320

Brands by name

Popular brands