manualshive.com logo in svg

Analog Devices ADuCM320, Hardware Reference Manual

The Analog Devices ADuCM320 is a powerful system-on-chip solution for IoT applications. For in-depth understanding and guidance on hardware integration, users can download the comprehensive Hardware Reference Manual for free from manualshive.com. This manual provides detailed instructions and specifications essential for successful product development.

Share
Download
background image

UG-498 

ADuCM320 Hardware Reference Manual

 

Rev. C | Page 4 of 196 

Wake-Up Timer ............................................................................ 169

 

Wake-Up Timer Features ........................................................ 169

 

Wake-Up Timer Block Diagram ............................................. 169

 

Wake-Up Timer Overview ...................................................... 169

 

Wake-Up Timer Operation ..................................................... 169

 

Register Summary: Wake-Up Timer ..................................... 172

 

Register Details: Wake-Up Timer .......................................... 172

 

PWM .............................................................................................. 176

 

PWM Features .......................................................................... 176

 

PWM Overview ........................................................................ 176

 

PWM Operation ....................................................................... 176

 

PWM Interrupt Generation .................................................... 179

 

Register Summary: PWM ....................................................... 180

 

Register Details: PWM ............................................................ 180

 

MDIO .............................................................................................  184

 

MDIO Features ......................................................................... 184

 

MDIO Overview ....................................................................... 184

 

MDIO Operation ...................................................................... 184

 

Block Switching ........................................................................ 186

 

Register Summary: MDIO Interface (MDIO) ...................... 191

 

Register Details: MDIO ........................................................... 191

 

Hardware Design Considerations .............................................. 194

 

Typical System Configuration ................................................ 194

 

Serial Wire Debug Interface .................................................... 196

 

 

 

REVISION HISTORY 

1/2017—Rev. B to Rev. C 

Changes to Clocking Architecture Operation Section .............. 12 
Changes to ADC Circuit Features Section .................................. 21 
Changes to ADC Circuit Overview Section ............................... 22 
Changes to Single-Ended Mode Section and Differential 
Section ..............................................................................................  23 
Changes to ADC Voltage Reference Selection Section.............. 26 
Changes to Table 23 ........................................................................ 34 
Added IDAC Thermal Shutdown Section ................................... 39 
Changes to Writing to Flash Section ............................................ 75 
Changes to Table 121 ...................................................................... 94 
Changes to Table 182 .................................................................... 130 

 
2/2016—Rev. A to Rev. B 

Changes to Table 7 .......................................................................... 14 
Changes to Table 12 ........................................................................ 28 
Changes to Protection, Integrity Section ..................................... 72 
Added ECC Error Handling Section, ECC Error During Read 
Section, and ECC Error During Execution of Sign Command 
Section ..............................................................................................  76 
Changes to Table 95 and Table 96 ................................................ 80 
Added ECC Enable/Disable, Error Response Register Section, 
Flash 0 ECC Error Address Register Section, Flash 1 ECC Error 
Address Register Section, and Table 112 to Table 114; 
Renumbered Sequentially .............................................................. 86 
Added MDIO Interrupt Power-Up Register Write Sequence 
Section ............................................................................................ 184 
 

1/2015—Rev. 0 to Rev. A 

Changes to Figure 1 .......................................................................... 1 
Changes to Register Access Conventions Section ........................ 6 
Changes to Introduction to the ADuCM320 Section .................. 7 
Moved Register Summary: Clock Architecture Section ............ 12 
Changes to Table 4 and Clocking Architecture Operation 
Section ..............................................................................................  12 

Change to Table 5 ........................................................................... 13 
Changes to Table 6 and Table 7 .................................................... 14 
Added Clocking Status Register Section and Table 8; 
Renumbered Sequentially ............................................................. 15 
Changes to Debug Support Section ............................................. 19 
Changes to ADC Voltage Reference Selection Section ............. 26 
Added Figure 8; Renumbered Sequentially ................................ 27 
Change to Table 14 ......................................................................... 30 
Changes to Table 16 ....................................................................... 31 
Changes to Table 17 ....................................................................... 32 
Changes to Table 22 ....................................................................... 33 
Changes to Table 25 ....................................................................... 36 
Changes to Case 2—Turn On IDAC2 but to Set the Output to 
0 mA with the Lowest Possible Offset Section ........................... 38 
Changes to Table 74 ....................................................................... 62 
Changes to Table 75 ....................................................................... 64 
Changes to Table 76 ....................................................................... 65 
Added Aborting DMA Transfers Section .................................... 65 
Changed Top of Flash Blocks Section to Reserved Flash 
Locations Section............................................................................ 73 
Changes to Erasing Flash Section and Signature Section ......... 74 
Changes to CPU Execution Speed Section ................................. 76 
Changes to Memory Cache Section ............................................. 77 
Changes to Table 95 and Table 96 ................................................ 79 
Changes to Cache Status Register Section .................................. 84 
Added Table 112 ............................................................................. 84 
Changes to Cache Setup Register Section and Cache Key 
Register Section .............................................................................. 85 
Added Table 113 and Table 114 .................................................... 85 
Deleted Shared MDIO Pins Section ............................................ 85 
Changes to Digital I/Os Features Section and Digital I/Os 
Overview Section............................................................................ 86 
Added Inaccessible Bits Section ................................................... 86 
Changes to I/O Pull-Up Enable (GPxPUL) Section .................. 87 
Changes to Open-Drain Enable (GPxODE) Section ................. 88 

Summary of Contents for ADuCM320





































































































































































































Reviews:

No comments

Related manuals for ADuCM320

Xilinx Virtex-II Pro ML300 Installation Instructions Manual preview
Virtex-II Pro ML300
Brand: Xilinx Pages: 17
IBASE Technology IB981 User Manual preview
IB981
Brand: IBASE Technology Pages: 92
ECS UM4980 User Manual preview
UM4980
Brand: ECS Pages: 46
Oki MSM7731-02 User Manual preview
MSM7731-02
Brand: Oki Pages: 24
ASROCK IMB-194-D Jumpers And Headers Setting Manual preview
IMB-194-D
Brand: ASROCK Pages: 2
Commell LE-380 User Manual preview
LE-380
Brand: Commell Pages: 49
Abit IS7-G User Manual preview
IS7-G
Brand: Abit Pages: 110
ST UM0920 User Manual preview
UM0920
Brand: ST Pages: 14
MSI MPG Z390 GAMING PLUS Quick Start Manual preview
MPG Z390 GAMING PLUS
Brand: MSI Pages: 76
Golden Motor EPO-03HP User Manual preview
EPO-03HP
Brand: Golden Motor Pages: 22
ASROCK FM2A78M-ITX+ Manual preview
FM2A78M-ITX+
Brand: ASROCK Pages: 153
Emerson MVME61006E-0161 Installation And Use Manual preview
MVME61006E-0161
Brand: Emerson Pages: 100
Emerson MVME6100 Series Installation And Use Manual preview
MVME6100 Series
Brand: Emerson Pages: 118
Emerson MVME51005E Installation And Use Manual preview
MVME51005E
Brand: Emerson Pages: 122
Emerson MVME7100 Installation And Use Manual preview
MVME7100
Brand: Emerson Pages: 138
Emerson MVME55006E Installation And Use Manual preview
MVME55006E
Brand: Emerson Pages: 146
Emerson MITX-430 Installation And Use Manual preview
MITX-430
Brand: Emerson Pages: 160
TYAN S2257 THUNDER 2400 Manual preview
S2257 THUNDER 2400
Brand: TYAN Pages: 105

Brands by name

Popular brands

Load more brands