Analog Devices ADuCM320 Hardware Reference Manual Download Page 29

Page: 29 / 196

ADuCM320 Hardware Reference Manual

UG-498

Rev. C | Page 29 of 196

REGISTER DETAILS: ADC CIRCUIT

ADC Configuration Register

Address: 0x40082174, Reset: 0x0280, Name: ADCCON

Table 13. Bit Descriptions for ADCCON

Bits

Bit Name

Description

Reset

Access

[15:11]

RESERVED

Reserved.

0x0

SOFT_RESET

Software reset ADC.

0x0

PUP

ADC power up.

0x1

0: power down

1: power up

RESERVED

Reserved.

0x0

REFB_PUP

ADC reference buffer power up.

0x1

0: power down

1: power up

Must be set to 1 for the ADC to operate normally

RESTART_ADC

Restart ADC, reset analog part of ADC. Active high.

0x0

0: normal ADC operation.

1: reset the ADC.

RESERVED

Reserved.

0x0

SEQ_DMA

DMA request enable for ADC sequence conversion.

0x0

0: disable ADC sequencer DMA access

1: enable ADC sequencer DMA access

CNV_DMA

DMA request enable for ADC non-sequence conversion.

0x0

0: disable ADC DMA access

1: enable ADC DMA access

[2:0]

C_TYPE

ADC conversion type.

0x0

00: no conversion

01: DIO pin starts conversion (P2.4)

10: single conversion

11: continuous conversion (use this mode for the sequencer)

100: PLA conversion

Summary of Contents for ADuCM320





































































































































































































Search results

Summary of Contents for ADuCM320

Reviews:

Related manuals for ADuCM320

Brands by name

Popular brands

Analog Devices ADuCM320, Hardware Reference Manual

Search results

Summary of Contents for ADuCM320

Reviews:

Related manuals for ADuCM320

Brands by name

Popular brands