![background image](http://html1.mh-extra.com/html/amx/modero-nxd-1200v/modero-nxd-1200v_operation-reference-manual_2938937074.webp)
Configuring Communication
62
NXD/T-1200V Wall/Flush Mount Touch Panel
10.
Click the
OnLine Tree
tab in the Workspace window to view the devices on the Virtual System.
The default System
value is one
.
11.
Right-click on the
Empty Device Tree/System
entry and select
Refresh System
to re-populate the list.
12.
Power-up your panel and press and hold the grey Front Setup Access button (
for 3 seconds
) to continue with the
setup process and proceed to the Setup page.
13.
Select
Protected Setup
>
System Settings
(located on the lower-left) to open the System Settings page (FIG. 65).
14.
Press the blue
Type
field (
from the Master Connection section
) until the choice cycles to the word
Ethernet.
ICSNet communication cannot be used on either 1200V-Series or VG-Series panels.
15.
Press the
Mode
field until the choice cycles to the word
URL
.
By selecting
URL
, the System Number field becomes read-only (grey) because the panel pulls this value
directly from the communicating target Master (virtual or not). A Virtual Master system value can be set
within the active AMX software applications such as: NetLinx Studio, TPD4, or IREdit.
16.
Press the
Master IP/URL
field to open a Keyboard and enter the IP Address of the PC used as the Virtual Master.
17.
Click
Done
to accept the new value and return to the System Settings page.
18.
Do not alter the Master Port Number value (
this is the default value used by NetLinx
).
19.
Press the
Back
button to open the Protected Setup page.
20.
Press the on-screen
Reboot
button to both save any changes and restart the panel.
Master Connection section - NetLinx Master Ethernet IP Address - URL Mode
In this mode, enter the System Number (
zero
for an unknown System Number) and the IP/URL of the Master (Master
Port Number is defaulted to
1319
).
1.
Press the blue
Type
field (
from the Master Connection section
) until the choice cycles to the word
Ethernet
. Refer
to the
System Settings Page
section on page 102 for more information about the fields on this page.
2.
Press the
Mode
field until the choice cycles to the word
URL
.
By selecting
URL
, the System Number field becomes read-only (grey) because the panel pulls this value directly
from the communicating target Master (virtual or not). A Virtual Master system value can be set within the active
AMX software applications such as: NetLinx Studio, TPD4, or IREdit.
3.
Press the
Master IP/URL
field to open a Keyboard and enter the Master IP Address
(obtained from the
Diagnostics - Networking Address dialog
of the NetLinx Studio application)
.
4.
Click
Done
to accept the new value and return to the System Settings page.
5.
Do not alter the Master Port Number value (
this is the default value used by NetLinx
).
6.
Enter a username and password (
into their respective fields
) if the target Master has been previously secured.
FIG. 65
Sample System Settings page (for Virtual Master communication)
Enter the IP Address
information of the PC
used as a Virtual
Master
The System Number is
assigned to the Master
within the AMX
software application
(these must match)
When using a Virtual Master,
there is no need to enter a
username and/or password
If the panel does not appear within the OnLine Tree tab of the Workspace window of
NetLinx Studio, check to make sure that the NetLinx Master System Number (from
within the Device Addressing dialog) is correctly assigned.
Summary of Contents for Modero NXD-1200V
