![background image](http://html1.mh-extra.com/html/amx/modero-nxd-1200v/modero-nxd-1200v_operation-reference-manual_2938937052.webp)
Installation Procedures: NXD-1200V Panels
40
NXD/T-1200V Wall/Flush Mount Touch Panel
Installing an NXD into an (optional) Rack Mount Kit (NXA-RK12)
1.
Remove the magnetic faceplate/bezel from the main NXD unit by gripping the faceplate and pulling with gentle
outward force.
2.
Thread the incoming RJ-45, Ethernet, USB, and any optional audio/video wiring through the opening in the
equipment rack (from their terminal locations). Refer to the
Wiring Guidelines for the 1200V Panels
section on
page 41 for pinout descriptions. Leave enough slack to accommodate any re-positioning of the panel.
3.
Connect all data and power wiring connectors to their corresponding locations along the side of the (un-powered)
NXD touch panel.
Verify the terminal end of the power cable is not connected to a power supply before plugging in the 2-pin
power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF transmitter.
4.
Test the incoming wiring by connecting the panel connections to their terminal locations and applying power. Verify
the panel is receiving power and functioning properly to prevent repetition of the installation.
5.
Disconnect the terminal end of the power cable from the connected power supply.
6.
Insert the main 12-inch Modero unit into an NXA-RK12 (FIG. 43).
7.
Secure the panel to the NXA-RK frame by first inserting and then tightening the four #4-40 screws (provided). Line
up the four mounting holes and use a grounded Phillips-head screwdriver to tighten the screws in a clockwise
direction.
8.
Insert the NXA-RK (with connected NXD unit) into the equipment rack, making sure to align the screw holes along
the sides on the NXA-RK with the holes in the equipment rack.
9.
Use a grounded Phillips-head screwdriver to secure the NXA-RK (with connected NXD unit) to the equipment rack
using #10-32 screws (not included).
10.
Place the magnet faceplate back onto the main NXD unit by gripping the faceplate and placing it on the housing
with gentle force.
Make sure to align the Microphone, Light, and PIR Motion sensor locations to their respective
openings on the front bezel/faceplate.
11.
Reconnect the terminal RJ-45, Ethernet, and any optional audio/video wiring to their respective locations on either
the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or NetLinx Master.
12.
Reconnect the terminal power connector on the 12 VDC-compliant power supply and apply power.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the necessary connectors before being inserted into the equipment rack.
FIG. 43
NXD-1200V 12 inch Wall Mount panel installed into an NXA-RK12 Rack Mount Kit
Faceplate
Rack mount
frame (NXA-RK12)
Summary of Contents for Modero NXD-1200V
