manualshive.com logo in svg

AMX Modero NXD-1200V, Operation/Reference Manual

Share
Download
AMX Modero NXD-1200V Operation/Reference Manual Download Page 18

Touch Panel Accessories

6

 NXD/T-1200V Wall/Flush Mount Touch Panel

Installing the NXA-AVB/ETHERNET

A 12 VDC-compliant power supply can indirectly provide power to a Modero panel by routing power through the NXA-
AVB/ETHERNET Breakout Box. FIG. 4 shows a sample wiring configuration using both an indirect or direct power 
connection for a video-capable Modero panel.   

  

   

A 12 VDC-compliant power supply can also directly provide power through the unit to a target Modero panel. FIG. 5 
shows a sample wiring configuration for a non-video capable Modero panel.   

  

Use a standard CAT5 Ethernet cable to provide both communication and 10/100 network connectivity between the panel, 
NXA-AVB/ETHERNET, NetLinx Master, and the network.

NXA-AVB/ETHERNET Specifications (Cont.)

Included Accessories:

• Two 2-pin Phoenix connectors (41-5025)

• 4-pin Phoenix connector (41-5047)

• 6-pin Phoenix connector (41-5063)

• Rack Mount Kit (KA2250-40) with mounting bracket (62-2254-02)

Other AMX Equipment:

• AC-RK Accessory RackMount Kit (

FG515

)

• Modero Table Top Cable (CA2250-50)

FIG. 4  

Sample wiring configuration on video-capable panels using this breakout box

FIG. 5  

Sample wiring configuration using CA Modero panels

NXD/T Video-capable

Ethernet In

12 VDC power

(RJ-45)

Video In

(BNC)

Mic Out

(4-pin captive-wire)

Audio In

(6-pin captive-wire)

NXA-AVB/ETHERNET

Power

supplied via

NXA-AVB box

Audio/Video
(CAT5)

Line Level out
(to amplifier
or VOL card)

Touch Panels

or

Direct

Connect

Breakout Box

Ethernet

(

rear

)

(

front

)

(CAT5)

supply

Indirect

Connect

12 VDC power

supply

Direct

connect

NXD/T Non-video capable

Ethernet
(CAT5)

Touch Panels

12 VDC power

Audio (CAT5)
between the
NXA-AVB/ETHERNET
Breakout Box

supply

The breakout box unit can be mounted on either a horizontal flat surface or into an 
equipment rack (by removing the front screws and attaching it to an optional AC-RK).
The power supply being used on the NXA-AVB/ETHERNET is dependant on the 
power requirements of the target touch panel.

Summary of Contents for Modero NXD-1200V

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands