![background image](http://html1.mh-extra.com/html/amx/modero-nxd-1200v/modero-nxd-1200v_operation-reference-manual_2938937109.webp)
Firmware Pages and Descriptions
97
NXD/T-1200V Wall/Flush Mount Touch Panel
Using the Automated Brightness Control feature (DIM Mode)
Please follow the steps below to set up Automated Brightness Control:
1.
Set the lighting conditions in the room to maximum (turn On all the lights).
2.
Set the Maximum Panel Brightness, from the Setup page, to a comfortable level.
3.
Open the Sensors Setup page (FIG. 97 on page 95) from the Protected Setup menu section.
4.
Move around the panel and block the direct or indirect light from the room fixtures with your body. Take note of the
drop in the lighting level being detected by the panel in response to your movements.
5.
Set the Maximum brightness of the Dimmer (
Dim Mode Max Level
) below the detected drop. This will make sure
that the panel does not react to variations in the lighting conditions of a normal working environment.
6.
Set the minimum lighting conditions in the room (not complete darkness but the minimal lighting setup, unless
complete darkness is an “operational option” for the room).
7.
Set the Minimum Dimmer Brightness (
Dim Mode Min Level
) to a comfortable level by sitting in front of the panel.
You should be able to comfortably see someone sitting behind the panel without being “blinded” by the panel.
8.
Move around the panel and block the direct or indirect light from the room fixtures with your body. Take note of the
drop in the lighting level being detected by the panel in response to your movements.
9.
Set the Minimum brightness of the Dimmer (
Dim Mode Max Level
) below the detected drop. This will make sure
that the panel does not react to variations in the lighting conditions of a normal working environment.
Sensor Setup Page Elements (Cont.)
Dim Mode Minimum
Brightness:
Allows you to alter the sensitivity of the Modero panel light sensor:
• Toggle the
Enable
/
Enabled
button to either active/inactive the DIM Mode feature:
-
Enable
- activates this feature. Once active (by receiving a value below the
Dim Mode Min Level value), the current light level ramps to the DIM Mode
value within a few seconds.
-
Enabled
- (
illuminated when selected
) deactivates this feature.
• Use the
DIM Mode Brightness
UP/DN buttons to alter the DIM level.
- Range = 0 - 100.
- The lower the value, the darker a room must be before the LCD Brightness value
changes to conform to a DIM room (and vice versa with a higher value).
• The
DIM Mode Minimum Brightness
bargraph indicates the current DIM Mode
Brightness level.
- This level corresponds to the brightness level of the LCD used when the DIM Mode is
active.
- The Brightness value of the panel in a DIM room (low-light) is much less than that of a
Non-DIM (well to brightly-lit) where the LCD Brightness must be higher to display the
screen content clearly.
There is a relationship between the motion sensor and the panel sleep feature. If a
panel is set to Sleep Mode, there is a time delay before the motion sensor is activated
to detect motion. By creating a time delay to the detection, this allows a user to set
the sleep mode and leave the panels’ detection range. In this way, the panel doesn’t
awake immediately after the sleep is active and you move away.
Sitting in front of the panel, you should be able to comfortably see someone sitting
behind the panel without being “blinded” by the panel.
The maximum (upper level) of the dimmer should be at least 15% lower than the
maximum detected level.
Summary of Contents for Modero NXD-1200V
