Amazone Cataya 3000 Super Operating Manual Download Page 87

Page: 87 / 252

Layout and function

Cataya Super BAH0087-11 01.19

The adjust the seed placement depth, the depth control disc/wheel (see Fig. 84) can be



engaged in 3 holes on the coulter



removed if the seed placement depth is not reached.

Hole

Placement

Shallow

Seeding without depth

control disc /

depth control wheel

Deep

Fig. 84

The handle (Fig. 85/1) is used to adjust the depth
control disc/wheel.

Fig. 85

The

seed placement depth

depends on the factors



Soil type (light to heavy)



Forward speed



Coulter pressure



Position of the depth control discs/wheels.

Summary of Contents for Cataya 3000 Super





























































































































































































































































Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands

Amazone Cataya 3000 Super, Operating Manual

Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands