manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 208

 

 

Cleaning, maintenance and repairs 

 

 

208

 

Cataya Super  BAH0087-11  01.19

 

12.3 

Shutdown of the implement over a long period of time 

Before parking the implement for a longer period of time 

 

Set the placement depth to "0" (only pack top seed drills with TwinTeC double disc coulters,  
see section "Adjusting and checking the seed placement depth", page 164. 

 

Thoroughly clean and dry the coulters. To prevent rust, protect the coulters with an 
environmentally friendly anti-corrosion agent. 

 

Set the coulter pressure to "0", see section "Coulter pressure, seed rate increase and coulter lift", 
page 168. 

 

Relieve the roller harrow with the central spanner to unload the formed rubber elements, see 
section "Setting the roller contact pressure", page 176. The formed rubber elements are used as 
a spring-loaded suspension for the roller harrow carrying arms. As a result, the roller harrow can 
follow the contours of the soil. 

 

Open the drain tap (Fig. 265/1) and drain 
the water out of the hand wash tank. 
 
Rinse the hand wash tank and leave the 
drain tap open (risk of freezing). 

 

 

Fig. 265 

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands