Amazone Cataya 3000 Super Operating Manual Download Page 21

Page: 21 / 252

General safety instructions

Cataya Super BAH0087-11 01.19

MD 076

Risk of drawing-in/entrapment for hand or
arm due to moving force-transmission parts!

This hazard can cause the most severe injuries
with loss of body parts.

Never open or remove protective equipment,



while the tractor engine is running with the
universal joint shaft or hydraulic/electronic
system connected.



if the ground wheel drive is moving.

MD 078

Risk of crushing of fingers/hand by
accessible, moving parts of the implement!

This hazard can cause the most severe injuries
with loss of body parts.

Never reach into the danger area when the
tractor engine is running with the universal joint
shaft or hydraulic / electronic system connected.

MD 082

Risk of falling when riding the implement on
treads or platforms!

Causes serious, potentially fatal injuries
anywhere on the body.

It is forbidden to ride on the implement or climb
the implement when it is running. This prohibition
also applies to implements with step surfaces or
platforms.

Make sure that nobody is riding on the
implement.

Summary of Contents for Cataya 3000 Super





























































































































































































































































Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands

Amazone Cataya 3000 Super, Operating Manual

Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands