manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 152

 

 

Settings 

 

 

152

 

Cataya Super  BAH0087-11  01.19

 

  8.  Calibrating the seed rate 

 

with the star wheel drive,  
see section "Calibrating the seed rate - implements with star wheel drive", page 153 

 

with the AmaDrill 2 control terminal and with ISOBUS system,  
see section "Calibrating the seed rate 
Implements with AmaDrill 2 control terminal, 
Implements with ISOBUS system", page 158. 

 

After calibration - Instructions 

  9.  After calibration, empty the two-part 

collection bucket (Fig. 191/1) into the seed 
hopper, put together, and push it into the 
holder up to the stop with the opening 
facing down. 

 

 

Fig. 191 

 10.  Engage the lever (Fig. 192/1) in the top of 

the elongated slot. 

 11.  Close the door for the control centre. 

 
The door for the control centre cannot be 
closed if 

 

the two-part collection bucket is not 
properly inserted into the holder 
(opening facing down). 

 

the lever (Fig. 192/1) is engaged at the 
bottom of the elongated slot. 

 

 

Fig. 192 

 

 

Repeat the calibration after seeding on approx. 1 hectare.  

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands