manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 233

 

 

 

Cleaning, maintenance and repairs

 

Cataya Super  BAH0087-11  01.19

 

233

 

12.8 

Lubrication 

The lubrication points on the implement are 
marked with the symbol (Fig. 323). 

 

 

Fig. 323 

 

Carefully clean the grease nipple and 
grease gun before lubrication so that 
no dirt is pressed into the bearings. 
Press the dirty grease completely 
into the bearings and replace it with 
new grease.

 

 

 

 

For lubrication work, use a lithium-
saponified multi-purpose grease 
with EP additives.

 

 

 

Fig. 324 

Company 

Lubricant designation 

ARAL 

Aralub HL2 

FINA 

Marson L2 

ESSO 

Beacon 2 

SHELL 

Ratinax A 

 

 

Fig. 324/… 

Component 

Number of  

grease nipples 

Lubrication  

interval 

Note 

1 

Setting spindle 
Seed placement 
Depth adjustment,  
see section 5.16.1,  
page 90 

4 

1x annually 

3 strokes with the grease 
gun hand  
lever for each grease nipple 

1 

Setting spindle 
Coulter pressure 
adjustment 
(manually actuated), 
see section 5.17.1,  
page 91 

4 

1x annually 

3 strokes with the grease 
gun hand  
lever for each grease nipple 

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands