manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 177

 

 

 

Settings

 

Cataya Super  BAH0087-11  01.19

 

177

 

8.11 

Moving the track marker to the working / transport position 

 

DANGER 

Secure the track markers immediately after work on the field 
(transport lock).  

Unsecured track markers could unintentionally move to the working 
position and cause serious injury. 

Only remove the transport lock for the track marker immediately 
before beginning field work.

 

 

 

WARNING 

Direct people out of the danger area. 

When actuating the tractor control unit, the hydraulic cylinders of the 
track marker and of the tramline marker can be actuated 
simultaneously. 

8.11.1 

Move track marker to working position 

In transport position, each track marker is 
secured with a bar (Fig. 234/1). 

 

 

Fig. 234 

  1.  Position the implement on the field. 

  2.  Unlock both track markers, see the "Soil 

tillage implement" operating manual. 

  3.  Direct people out of the swivel area of the 

track marker. 

  4.   To adjust the track discs, swing the track 

markers into working position, one after the 
other.  

 

  If the seed drill has the ISOBUS system, 

you can swing both track markers into 
working position simultaneously, see 
"ISOBUS Software" operating manual. 

 

 

Fig. 235 

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands