manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 8

 

 

 

 

 

 

8

 

Cataya Super  BAH0087-11  01.19

 

8.11

 

Moving the track marker to the working / transport position ............................................... 177

 

8.11.1

 

Move track marker to working position ................................................................................ 177

 

8.11.2

 

Moving the track marker to transport position ..................................................................... 179

 

8.12

 

One-sided switching ............................................................................................................ 180

 

8.12.1

 

One-sided switching on seed drills with two seeding shaft drive motors ............................ 180

 

8.12.2

 

One-sided switching  on implements with one seeding shaft drive motor or with star 
wheel drive .......................................................................................................................... 181

 

8.13

 

Moving the tramline marker into working/transport position................................................ 182

 

8.13.1

 

Move the tramline marker to working position .................................................................... 182

 

8.13.2

 

Move the tramline markers to the transport position ........................................................... 183

 

8.14

 

Moving the exact following harrow road safety bar into road transport/parking 
position ................................................................................................................................ 184

 

8.14.1

 

Moving the road safety bar into road transport position ...................................................... 184

 

8.14.2

 

Moving the transport safety bar into parking position ......................................................... 184

 

9

 

Transportation ......................................................................................... 185

 

9.1

 

Moving the seeding combination into transport position ..................................................... 185

 

9.2

 

Legal regulations and safety ............................................................................................... 186

 

10

 

Use of the implement .............................................................................. 190

 

10.1

 

Initial operation .................................................................................................................... 191

 

10.2

 

Headlight ............................................................................................................................. 191

 

10.3

 

Moving the implement from transport into working position ................................................ 192

 

10.4

 

Work commencement ......................................................................................................... 192

 

10.5

 

During operation .................................................................................................................. 194

 

10.5.1

 

Overview of checks during operation .................................................................................. 194

 

10.5.2

 

Turning at end of the field ................................................................................................... 195

 

10.5.3

 

Track marker ....................................................................................................................... 196

 

10.5.4

 

End of work on the field ....................................................................................................... 197

 

10.6

 

Emptying the seed hopper and seed housing ..................................................................... 198

 

11

 

Faults ........................................................................................................ 202

 

11.1

 

Residual seed quantity display ............................................................................................ 203

 

11.2

 

Deviations between the set and actual seed rate ............................................................... 203

 

12

 

Cleaning, maintenance and repairs ....................................................... 204

 

12.1

 

Safety .................................................................................................................................. 204

 

12.2

 

Cleaning the machine ......................................................................................................... 206

 

12.3

 

Shutdown of the implement over a long period of time ....................................................... 208

 

12.4

 

Setting and repair work (specialist workshop) .................................................................... 209

 

12.4.1

 

Opening and closing the function flap ................................................................................. 209

 

12.4.2

 

Opening and closing the cover ............................................................................................ 210

 

12.5

 

Tramline control ................................................................................................................... 211

 

12.5.1

 

Folding down the countershaft ............................................................................................ 213

 

12.5.2

 

Folding up the countershaft ................................................................................................. 214

 

12.5.3

 

Setting the tramline track width ........................................................................................... 215

 

12.5.4

 

Setting the tramline wheelmark width ................................................................................. 216

 

12.5.5

 

Conversion of a metering wheel to a tramline metering wheel ........................................... 217

 

12.5.6

 

Conversion of a tramline metering wheel to a metering wheel ........................................... 219

 

12.5.6.1

 

Conversion of a tramline metering wheel to a metering wheel  by shifting the gear 
wheel on the countershaft ................................................................................................... 219

 

12.5.6.2

 

Conversion of a tramline metering wheel to a metering wheel  by removing the gear 
wheel pairing from the lay shaft and seeding shaft ............................................................. 220

 

12.6

 

Changing the metering wheel ............................................................................................. 221

 

12.6.1

 

Changing the metering wheel - Seeding shaft drive with star wheel .................................. 221

 

12.6.2

 

Changing the metering wheel - Seeding shaft drive with one or two electric motors ......... 226

 

12.7

 

Repositioning the bevel gears in star wheel gearbox 1 ...................................................... 231

 

12.8

 

Lubrication ........................................................................................................................... 233

 

12.9

 

Maintenance schedule ........................................................................................................ 234

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands