manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 186

 

 

Transportation 

 

 

186

 

Cataya Super  BAH0087-11  01.19

 

17.  Switch on the warning beacon and check operation before driving off ............................ Page 186 

9.2 

Legal regulations and safety 

When driving on public streets or roads, the tractor and implement must comply with the national road 
traffic regulations (in Germany the StVZO and the StVO) and the accident prevention regulations (in 
Germany those of the industrial injury mutual insurance organisation).  

The vehicle keeper and driver are responsible for compliance with the statutory stipulations. 

Furthermore, the instructions in this section have to be complied with prior to starting and during 
travel. 

 

Transport width/Transport height 

In Germany and in many other countries, the transportation of a implement combination up to 3.0 m 
width mounted on the tractor is permissible. 

The max. transport height of 4.0 m must not be exceeded! 

 

Max. permissible speed 

The max. permissible speed 

1)

 is 40 km/h for tractors with mounted implements. 

In particular on bad roads and ways driving may only take place at a considerably lower speed than 
specified! 

1)

 The permissible maximum speed for mounted agricultural implements differs in the various 

countries according to national traffic regulations. Ask your local importer/implement dealer about 
the maximum permitted speed for road travel. 

 

Warning beacon 

In several countries, the implement and/or the tractor must be equipped with a warning beacon. Ask 
your local importer/implement dealer about the legal guidelines. The warning beacon is subject to 
approval in Germany.  

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands