Amazone Cataya 3000 Super Operating Manual Download Page 193

Page: 193 / 252

Use of the implement

Cataya Super BAH0087-11 01.19

193

4. Check all of the implement settings, see section "Settings", page 141.

5. Instruct any people in the area to stand at a minimum distance of 20 m from the implement.

6. Release the transport lock for the track markers

see "Soil tillage implement" operating manual.

7. Switch on the control terminal, see "Control terminal" operating manual.

8. Move track markers into working position, page 177.

9. Calibrate the working position (A) and

transport position (B) on the field



with ISOBUS system: see
"ISOBUS Software" operating manual

The settings can be made so that the electric
motor that drives the seeding shaft



starts rotating as soon as the seed drill
coulters penetrate into the soil.



comes to a stop as soon as the seed
drill coulters come out of the soil.

Fig. 254

10. Actuate the tractor control unit (yellow):



Lower the active track marker.



Advance the tramline control



Creation of tramlines (if required)



Lowering the tramline marker (if necessary).

11. Set the tramline counter just before commencing the first field run,



see "ISOBUS software" operating manual



see "AmaDrill 2" operating manual.

12. Run the PTO shaft of the soil tillage implement up to operating speed

see "Soil tillage implement" operating manual.

13. Start off and lower the combination using the tractor's 3-point hydraulic system.

Summary of Contents for Cataya 3000 Super





























































































































































































































































Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands

Amazone Cataya 3000 Super, Operating Manual

Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands