manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 195

 

 

 

Use of the implement

 

Cataya Super  BAH0087-11  01.19

 

195

 

10.5.2 

Turning at end of the field 

 

DANGER 

After turning, with the corresponding pre-selection on the 
control terminal and when the tractor control unit is actuated, 
the opposite track marker is moved to the working position. 

 

  1.  Actuate the tractor control unit (yellow). 

 

  Raise the active track marker 

 

  Advance the tramline counter 

 

  Raise the track disc of the tramline marker. 

  2.  Operate the control unit for the tractor lower link. 

 

  Raise the combination. 

  3.  Turn the combination. 

 

 

The coulter and harrow must not contact the ground during turning. 

 

Raising the combination before turning at the end of the field interrupts the seed supply by stopping 
the seeding shaft. 

After turning at the end of the field 

  1.  Start. 

  2.  Operate the control unit for the tractor lower link. 

  Lower the combination. 

  3.  Actuate the tractor control unit (yellow) for at least 5 seconds so that all hydraulic functions are 

fully executed. 

  Lower the active track marker. 

  Lower the track disc of the tramline marker to create tramlines. 

  4.  Start the field run. 

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands