manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 151

 

 

 

Settings

 

Cataya Super  BAH0087-11  01.19

 

151

 

8.4 

 

Calibrating the seed rate 

  1.  Couple the implement combination to the tractor, see section "Coupling and uncoupling 

implements", page 125. 

  2.  Park the combination on a level surface.  

  3.  Secure the tractor against unintentional start-up  

and unintentional rolling away. 

 

Do not switch off the tractor power supply, if your implement  

 

is equipped with an ISOBUS system or 

 

is equipped with a seeding shaft drive motor.  

The tractor power supply is required to operate the control terminal 
and the seeding shaft drive motor. 

 

  4.  Open the door for the control centre. 

  5.  Pull the two-part collection bucket  

(Fig. 189/1) slightly out of the holder, turn it 
around and push it into the holder under the 
seed hopper up to the stop with the bucket 
opening facing up.  

 

 

Fig. 189 

  6.  Guide the metered seed into the collection 

buckets. 

 6.1  Push the lever (Fig. 190/1) downward 

in the slotted hole to the stop. 

 6.2  Push the lever back until the lever 

engages (see Fig. 190). 

 

 

Fig. 190 

 

  7.  Fill at least 1/3 of the seed hopper volume with seed, except for fine seed, see section "Fill the 

seed hopper", page 144. Reduce the filling quantity accordingly for fine seed. 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands