Amazone Cataya 3000 Super Operating Manual Download Page 142

Page: 142 / 252

Settings

142

Cataya Super BAH0087-11 01.19

8.1

Folding the steps up and down

DANGER

Never climb onto the steps and the loading board when the seed
drill is parked on the supports (risk of tipping).

Climbing up is only permitted when the seed drill is coupled to the soil
tillage implement.

CAUTION

Only step onto the loading board via the steps.

Climbing onto the loading board without using the steps can lead to
serious injuries due to falling.

Always fold up the steps before starting operation or road transport.

DANGER

A latch (Fig. 173) represents the
mechanical transport locking
mechanism for the steps.

Check the latch (arrow) for proper
seating after folding in the steps.

Fig. 173

Summary of Contents for Cataya 3000 Super





























































































































































































































































Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands

Amazone Cataya 3000 Super, Operating Manual

Search results

Summary of Contents for Cataya 3000 Super

Reviews:

Brands by name

Popular brands