manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 185

 

 

 

Transportation

 

Cataya Super  BAH0087-11  01.19

 

185

 

9 

Transportation 

 

 

DANGER 

In Germany and several other 
countries, the transportation of 
implements mounted on the tractor 
on public roads and routes is 
approved up to a width of 3.0 m. 

 

 

Fig. 249 

Transport of a combination over 3.0 m wide is 
only permitted on a transport vehicle in these 
countries. Place and secure the combination 
consisting of soil tillage implement, roller and 
pack top seed drill on the transport vehicle in 
accordance with regulations. Do not exceed the 
max. transport height of 4.0 m. 

Read the transport width of the seed drill and soil 
tillage implement combination from both 
operating manuals. The data can be found in the 
"Technical data" section. 

 

9.1 

Moving the seeding combination into transport position 

 1.  If the implement is equipped with coulter lift and the coulters are lifted, move the 

coulters and harrow into working position ........................................................................ Page 168 

 2.  Press the pause button on the control terminal (if required).  

Pressing the pause button before folding the track markers prevents the tramline 
counter from advancing by one digit.  

 3.  Fold and secure the track markers,  

see "Soil tillage implement" operating manual 

 4.  Move the pulse wheel to the transport position ................................................................ Page 159 

 5.  Move the tramline markers to the transport position ........................................................ Page 182 

 6.  Move the exact following harrow into transport position ................................................... Page 174 

 7.  Move the road safety bar of the exact following harrow into transport position ............... Page 184 

 8.  Empty the seed hopper if one of the permissible values for the total tractor weight, 

axles loads and tyre load-bearing capacity is exceeded when the seed hopper is 
full (see also section "Checking the suitability of the tractor", page 115) ......................... Page 198 

 9.  Close the seed hopper cover. 

10.  Fold up the steps .............................................................................................................. Page 142 

11.  Switch off the floodlights ................................................................................................... Page 191 

12.  Switch off the control terminal (see the "Control terminal" operating manual) 

13.  Check the lighting system and warning signs for proper function and cleanliness ............ Page 50 

 14.  Check that the parking supports have been removed.  

The parking supports do not have a locking device. When transporting the combination, they can 
accidentally wander out of the mounts and cause serious accidents. 

15.  Disable the tractor control units required for operating the implement  

(see also tractor operating manual) .................................................................................... Page 47 

16.  Read and observe section 9.2:  

Legal guidelines and the safety instructions before and during road transport. 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands