manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 132

 

 

Coupling and uncoupling the implement 

 

 

132

 

Cataya Super  BAH0087-11  01.19

 

 12.  Raise the combination so that the parking 

supports are just above the ground. 

 13.  Remove the parking supports (Fig. 149/1). 

 

 

Fig. 149 

 

 

DANGER 

Remove the parking supports immediately after coupling the 
seed drill on the soil tillage implement.  

The parking supports do not have a locking device. When transporting 
the combination, they can accidentally wander out of the mounts and 
cause serious accidents.  

 
Connect the hydraulic hose (Fig. 150/1) for the 
track markers. 

 

 

Fig. 150 

 14.  Connect the plug (Fig. 151/1): 

 

Plug and socket connection  
lighting on the left for road travel. 

 

Plug and socket connection  
lighting on the right for road travel. 

 

 

Fig. 151 

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands