manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 162

 

 

Settings 

 

 

162

 

Cataya Super  BAH0087-11  01.19

 

8.6.1.1 

Adjusting the depth control discs / wheels 

If the desired placement depth cannot be achieved by adjusting the coulter pressure, adjust or remove 
all of the depth control discs/wheels equally, as described in this section.  

Engaging the depth control disc/wheel in one of the holes on the coulter 

  1.  Read the required hole for the depth control 

disc/wheel from the table (Fig. 84, page 87). 

  2.  Insert the shoulder of the depth control 

disc/wheel into the required hole. The lever 
(Fig. 206/1) is used to actuate the depth 
control disc/wheel.  

  3.  Adjust all of the depth control discs/wheels 

equally. 

 

 

Fig. 206 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands