manualshive.com logo in svg

Amazone Cataya 3000 Super, Operating Manual

Share
Download
Amazone Cataya 3000 Super Operating Manual Download Page 158

 

 

Settings 

 

 

158

 

Cataya Super  BAH0087-11  01.19

 

8.4.2 

Calibrating the seed rate 
Implements with AmaDrill 2 control terminal, 
Implements with ISOBUS system 

  1.  Prepare the implement for calibration, see 

section "  Calibrating the seed rate",  
page 151. 

  2.  Pre-calibrate the seed drill.  

 2.1  Pre-calibrate the seed drill according 

to the "ISOBUS software" operating 
manual. 
Pre-calibration creates the same 
conditions as when driving on the field 
later on. 

 2.2  Empty the two-part collection bucket 

(Fig. 191/1) into the seed hopper, put 
together, and push it into the holder up 
to the stop with the opening facing up. 

 

 

Fig. 200 

  3.  Calibrating the seed rate. 

 3.1  Calibrate the seed drill according to 

the "ISOBUS software" operating 
manual. 

 3.2  Fold out the bracket (Fig. 201/1) for 

weighing the collected seed. 

 3.3  Weigh the content of the collection 

bucket in the collapsible bucket. 

 

 

Fig. 201 

 

Check the scales to ensure the display 
is accurate, taking the container weight 
into consideration. 

 

  4.  Repeat the calibration test until the desired 

seed rate is achieved. 

 

 

Summary of Contents for Cataya 3000 Super





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands