manualshive.com logo in svg

YOKOGAWA AQ6370D, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ6370D Скачать руководство пользователя страница 37

3-7

IM AQ6370D-01EN

Preparing for Measurement

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

App

Index

3.4  Turning the Power ON/OFF

Before Connecting the Power

Take the following precautions before turning on the power supply. Failure to do so can 
result in electric shock or damage to instruments. 

 WARNING

•  Before connecting the power cord, ensure that the power supply source voltage 

matches the rated supply voltage of the instrument and that it is within the 
maximum rated voltage of the provided power cord. 

•  Check that the instrument’s power switch is OFF before connecting the power 

cord. 

•  To prevent the possibility of electric shock or fire, always be sure to use the 

power cord supplied for the instrument by YOKOGAWA. 

•  Make sure to implement protective earth grounding to prevent electric shock. 

Connect the instrument’s power cord into a three-prong electrical outlet with a 
protective grounding terminal. The AC outlet must be of a three-prong type with 
a protective earth ground terminal. 

•  Do not use an extension cord without protective earth ground. Otherwise, the 

protection function will be compromised. 

•  Use an outlet that is compatible with the accessory power cord, and be sure to 

connect protective grounding. Do not use the instrument if the power outlet does 
not provide appropriate protective grounding. 

Preparing to Turn ON the Power

The AQ6370D has a 

MAIN POWER 

switch for turning the main power ON/OFF, and a 

POWER

 switch for starting and shutting down the instrument. 

The POWER

 switch is a 

push-button switch; press once to turn it ON and press again to turn it OFF. 
•  Confirm that the 

MAIN POWER 

switch on the rear panel of the instrument is OFF. 

•  Connect the power cord plug to the power connector on the rear panel.
•  Connect the other end of the cord to an outlet that meets the following conditions. Use 

a grounded three-prong outlet.

Item

Rated supply voltage*

100 VAC to 240 VAC

Permitted supply voltage range

90 VAC to 264 VAC

Rated power supply frequency

50/60 Hz

Permitted supply frequency range

48 Hz to 63 Hz

Maximum power consumption

Approx. 100 VA

*  This instrument can use a 100 V or a 200 V power supply. The maximum rated voltage differs 

according to the type of power cord. Before you use the instrument, check that the voltage 

supplied to it is less than or equal to the maximum rated voltage of the power cord provided 

with it (see page iii of the 

Getting Started Guide

, IM AQ6370D-02EN, for the maximum voltage 

rating).

Содержание AQ6370D






























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды