YOKOGAWA AQ6370D Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 445

YOKOGAWA AQ6370D Скачать руководство пользователя страница 32

3-2

IM AQ6370D-01EN

Also be sure to maintain sufficient clearance for connecting measurement cables.

20 cm or

more

20 cm or more

20 cm or

more

20 cm or

more

Inlet holes (also on the bottom panel)

Ambient Temperature and Humidity

Ambient temperature: 5 to 35°C
Ambient humidity: 80% RH or lower (no condensation present)

Note

Condensation may occur if the instrument is moved to another place where the ambient
temperature is higher, or if the temperature changes rapidly. In such cases, allow sufficient time
for the instrument to adjust to the ambient temperature before use.
When the instrument is packaged in a box and moved, prevent condensation by allowing
sufficient time for the instrument to acclimatize before removing it from the box.

Do Not Install the Instrument in the Following Places

• Outdoors.
• Dangerous locations where flammable or explosive gasses, vapors, or dust is present,

or where the possibility of explosions or fires exists.

•  In direct sunlight or near heat sources.
•  Where an excessive amount of soot, steam, dust, or corrosive gas is present.
•   Location where mechanical vibration is high.
•  In an unstable place.
•  Where the instrument is exposed to water or other liquids.

General Handling Precautions

• Do Not Place Anything on Top of the Instrument

Never stack instruments or place any other objects on top of the instrument, especially

those containing water. Doing so can lead to malfunction.

• Take Proper Care When Carrying the Instrument

The instrument should always be carried by two people. Hold the instrument by the

handles on the sides of the case. The instrument weighs approximately 19 kg. Take
precautions against injuries when carrying it. Also, always turn the power switch OFF,
remove the power cable, and confirm that no other cables are connected before
carrying the instrument.

• Clean the Instrument Properly

When removing dirt from the case or operation panel, disconnect the power to the

circuits under test and the instrument, remove the instrument’s power cord from the
power outlet, then wipe gently with a clean, dry cloth. Do not use volatile chemicals
since this might cause discoloring and deformation.

3.1 Installing the Instrument

«
...
30
31
32
33
34
...
»

Содержание AQ6370D






























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды