manualshive.com logo in svg

YOKOGAWA AQ6370D, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ6370D Скачать руководство пользователя страница 115

5-46

IM AQ6370D-01EN

Explanation

Data measurement or signal sweeping starts when triggered by an external signal. 
An external trigger input terminal is located on the rear panel of the instrument. Input 
signals are of TTL levels. 
SMPL TRIG: 

 Measurement starts per external trigger signals. You can set 
whether the trigger activates on a rising or falling edge of the signal. 
Measurement starts approximately 70 µs after the trigger activates. 

SWEEP TRIG:   Sweeping starts per external trigger signals. The trigger activates on 

the rising/falling edge of the signal. Sweeping starts 5 ms at most after 
the trigger activates.

SMPL ENABLE:   A single or repeat sweep starts when the external trigger signal level is 

low. The sweep is stopped when the signal level becomes high. If the 
signal level becomes low again, the sweep starts from the point that it 
stopped at.

Signal Logic and Delay Time (for SMPL TRIG)

EDGE

This key is used to set the external trigger signal detection edges.
RISE:  The rising edge is recognized as a trigger.
FALL:  The falling edge is recognized as a trigger.

DELAY  ****.*µs

This key is used to set the delay time between trigger signal edge detection and data 
measurement. The setting range is 0 to 1000.0 µs (fine: steps of 0.1; coarse: steps of 1). 
For information about the external trigger measurement function, see section 2.2. 

Measurement Sensitivity and Corresponding Pulse Width

When SMPL TRIG or SWEEP TRIG Is Selected

The measurement sensitivity is determined based on the light pulse width. Select the 
appropriate sensitivity level based on the pulse width in the table below. 

  Sensitivity Name and Corresponding Pulse Width

Sensitivity 

setting

CHOP 

MODE

On-Screen Notation 

Corresponding  

Pulse  Width  

(Min.)

Normal

PEAK HOLD 

Setting

EXT TIRG

Setting

NORM/HOLD

OFF

NORM/HOLD P-NORM/HLD E-NORM/HLD

PEAK: 100 µs 

EXT:    50 µs

NORM/AUTO

NORM/AUTO P-NORM/AUT E-NORM/AUT

300 µs

NORMAL

NORMAL

P-NORMAL

E-NORMAL

1 ms

MID

MID

P-MID

E-MID

3 ms

HIGH1

HIGH1

P-HIGH1

E-HIGH1

10 ms

HIGH2

HIGH2

P-HIGH2

E-HIGH2

50 ms

HIGH3

HIGH3

P-HIGH3

E-HIGH3

200 ms

MID

SWITCH

MID/SW

P-MID/SW

E-MID/SW

3 ms

HIGH1

HI1/SW

P-HI1/SW

E-HI1/SW

10 ms

HIGH2

HI2/SW

P-HI2/SW

E-HI2/SW

50 ms

HIGH3

HI3/SW

P-HI3/SW

E-HI3/SW

200 ms

5.16  External Trigger Measurement

Содержание AQ6370D






























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды