Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 130

background image

BA 5001-6001 US – Edition 1.2 * 6001b110.fm

1-9

Introduction

1.9

Labels

The following symbols are displayed on the machine to provide pictorial information to the
user. The information and explanations are provided to avoid misinterpretation by the user.
The symbols have been selected from standards to provide important information to those
involved with operating, adjusting, maintaining and repairing this machine.

Description

Recommended tire inflation pressure.

Location (6001)

On the side of the dump bucket and the mudguards

Description

Recommended tire inflation pressure.

Location (5001)

On the side of the dump bucket and the mudguards

Description

Machine eye hooks

– see chapter 3.26

Lifting the machine

on page 3-40

Location

On the frame member just above the articulation joint, next to the lifting point.

Description

Lifting instructions

– see chapter 3.28

Tying down the machine

on page 3-42

Location

On the chassis

Description

Noise levels produced by the machine.
L

WA

= sound power level

Other information

– see chapter 6.12

Noise levels

on page 6-7

Location (6001)

On the engine cover

Fig. 6:

Tire pressure label

Fig. 7:

Tire pressure label

Fig. 8:

Lifting point

Hebeband

lifting belt

Elingue en ruban

Kranhaken
hook of crane
Crochet de grue

Huböse

stop eye

Eilleton de levage

Bügel
handle
Etrier

Knicksperre einlegen

fasten articulation resistance

Appliquer le dispositif de blocage de l´articulation

9705487

Fig. 9:

Label with indications for loading the machine

9705542

Fig. 10: Noise level

«
...
15
16
17
18
19
...
»

Содержание Dumper 5001



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dumper 5001

Бренд: Danelec Страницы: 67

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренд: campgo Страницы: 33

Бренд: Tascam Страницы: 3

Бренд: Mako Страницы: 17

BOS R254K-UUI-LH10-S4

Бренд: Balluff Страницы: 12

Бренд: Valko Страницы: 10

ABS-Lock III-BE

Бренд: ABS Страницы: 8

Бренд: V-GREAT Страницы: 4

Бренд: Interacoustics Страницы: 25

Бренд: Hamilton Beach Commercial Страницы: 32

Бренд: FoodMarble Страницы: 44

Бренд: ISA Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды