Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 130

background image

5-24

BA 5001-6001 US – Edition 1.2 * 6001b520.fm

Maintenance

Checking hydraulic pressure lines

Specific safety instructions

WARNING

Pressurized hydraulic oil hazard. Hydraulic oil escaping under high pressure
can catch fire, damage property, penetrate the skin and cause severe burns
and injuries.

☞

Do not operate the machine with leaking or damaged hydraulic system
components.

☞

Use a piece of cardboard to diagnose the source of hydraulic leaks.

☞

Hydraulic oil can be hot and may cause serious burns if contact is made
with skin. If contact occurs with hot oil, seek immediate medical attention
and treatment for the burn.

☞

Wear safety glasses to avoid eye contact. If oil contacts the eye flush
immediately with clean water and seek emergency medical treatment.

☞

Seek immediate medical attention if oil penetrates the skin. Oil may cause
serious infections.

☞

Retighten leaking threaded fittings and hose connections only when the
system is not under pressure; i.e. release the pressure before working on
pressurized lines.

☞

Never weld or solder damaged or leaking pressure lines and threaded fit-
tings. Replace damaged parts with new ones.

☞

Do not check for leaks with an incandescent light or open flame due to
explosive fire risk from vaporized oil mist.

• Leaks and damaged pressure lines must be immediately repaired or replaced by an

authorized service facility or after-sales staff.
This not only increases the operating safety of your machine but also helps to protect
the environment.

• Replace hydraulic hoses every 6 years from the date of manufacture, even if they do

not seem to be damaged.

In this respect, we recommend that you observe all the relevant safety regulations for
hydraulic lines, as well as the safety regulations regarding accident prevention and occu-
pational health and safety in your country. Also observe DIN 20066, part 5.

«
...
100
101
102
103
104
...
»

Содержание Dumper 5001



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dumper 5001

Бренд: FENDT Страницы: 31

Бренд: Keithley Страницы: 42

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: OceanSat Страницы: 85

Бренд: h/p/cosmos Страницы: 81

Бренд: Idmed Страницы: 2

Бренд: Ultraflex Страницы: 3

Бренд: FARM-MAXX Страницы: 35

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

Бренд: Qtx Страницы: 6

Бренд: Hussmann Страницы: 20

Бренд: Halemeier Страницы: 2

Бренд: IRUDEK Страницы: 19

Бренд: Fagor Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды