Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 91

Страница: 91 / 130

BA 5001-6001 US – Edition 1.2 * 6001b510.fm

5-13

Maintenance

Checking the coolant level

☞

Proceed as follows:

• Park the machine on level ground.
• Stop the engine!
• Remove the key and carry it with you.
• Let the engine and the coolant cool down.
• Open the engine cover.
• Check the coolant level on the transparent coolant tank

and on the radiator

☞

If the coolant level is below the

LOW

seam or if there is no coolant at the radiator's

filler inlet:

• Add coolant to the coolant tank.

Important

Check the coolant level once a day.
We recommend checking it before starting the engine.

Filling up coolant

After the engine has cooled down:

☞

Release overpressure in the radiator

☞

Carefully open the cap to the first notch and fully release the pressure

☞

Open filler cap B

☞

Add coolant up to the lower edge of the filler inlet (radiator)

☞

Close filler cap B

☞

Start the engine and let it warm up for about 5 – 10 minutes

☞

Stop the engine

☞

Remove the key and carry it with you

☞

Let the engine cool down

☞

Check the coolant level again

➥

The coolant level must be between the

LOW and FULL

tank seams

☞

If necessary, add coolant and repeat the procedure until the coolant level remains
constant

Important

Check the antifreeze every year before the cold season sets in!

Fig. 78: Expansion tank for coolant (6001)

LOW

FULL

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды