Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 130

background image

BA 5001-6001 US – Edition 1.2 * 6001b320.fm

3-11

Operation

Indicators and warning lights: overview

1 Not assigned

2 High beam indicator (blue)

Comes on if high beam is on.

CAUTION

Make sure no other road users are blinded by lights.

☞

Switch on low beam when other road users are nearby.

3

Preheating indicator (yellow)

Comes on if the key in the preheating start switch is in position

2

.

A glow plug preheats the air in the combustion chamber of the engine when the key is in
this position.
The indicator goes out as soon as preheating temperature is reached (15 – 20 sec)

4

Hydraulic oil filter indicator (red)

Indicates inadmissibly high pressure in the hydraulic return line to the tank. In this case:

☞

Have the hydraulic oil return filter checked and, if necessary, replaced by an authorized
service facility

☞

The indicator can come on briefly if the hydraulic oil is cold, but goes out again once
operating temperature is reached.

5 Not assigned

6

Indicator (red)—alternator charge function

NOTICE:

The coolant pump no longer runs if the V-belt is faulty. Engine may

overheat or break down. If the indicator comes on with the engine running:

☞

Stop the engine immediately.

☞

Have the cause repaired by an authorized service facility.

The V-belt for the alternator, or the charging circuit of the alternator is faulty if the indicator
comes on with the engine running. The battery is no longer charged.

7 Parking brake indicator (red)

Comes on if the parking brake is applied.
In this case:

☞

Actuate lever

18

to release the parking brake

«
...
41
42
43
44
45
...
»

Содержание Dumper 5001



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dumper 5001

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: Canta Страницы: 2

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: Cadex Страницы: 300

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jaga Страницы: 32

Бренд: RAPID REBOOT Страницы: 18

Бренд: MacDon Страницы: 170

Бренд: MacDon Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды