Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 98

Страница: 98 / 130

5-20

BA 5001-6001 US – Edition 1.2 * 6001b520.fm

Maintenance

Checking the hydraulic oil level

WARNING

Personal injury hazard. Escaping oil may cause serious injuries.

☞

Never fill the oil level above the MAX mark.

☞

Check the hydraulic oil level each time the machine is put into operation or
once a day

☞

Proceed as follows:

• Park the machine on level ground.
• Retract all hydraulic rams.

☞

Fully dump in the dump bucket.

• Stop the engine.
• Check the oil level on sight glass

• A gauge element in sight glass

indicates the oil level.

If the oil level is lower

• Add hydraulic oil.

The oil level must be at the

FULL

level.

The oil level varies according to the machine's operating temperature:

Important

Measure the oil level of the hydraulic system only after the machine reaches its
operating temperature.

Fig. 84: Oil level gauge

Machine condition

Temperature

Oil level

• Before putting into operation Between 10 and 30 °C (50 and 86 °F)

LOW

mark

• Normal operation

Between 50 and 90 °C (122 and 194 °F)

FULL

mark

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды