Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 110

Страница: 110 / 130

5-32

BA 5001-6001 US – Edition 1.2 * 6001b530.fm

Maintenance

Exterior of the machine

NOTICE:

Cleaning the machine improperly may cause engine damage.

☞

Follow the recommendations below to properly clean the machine and the engine.

The following articles are generally suitable:

• High-pressure cleaner
• Steam jet

Engine compartment

CAUTION

Crushing, cutting, or burn hazards.

☞

Stop the engine before cleaning.

NOTICE:

Possible sensor damage. Water or steam jet cleaners can penetrate

sensitive electronic components, leading to sensor failure and possible engine
damage.

☞

Allow the machine to cool completely before cleaning the engine with a water or steam
jet.

☞

Do not point the jet directly at electric sensors such as the oil pressure switch.

Threaded fittings and attachments

All threaded fittings must be checked regularly for tightness, even if they are not listed in
the maintenance schedules.

☞

Engine fastening screws.

☞

Fastening screws on the hydraulic system.

☞

Line and pin fastenings on the attachment.

Retighten loose connections immediately. Contact an authorized service facility if
necessary.

Pivots and hinges

Lubricate all mechanical pivots on the machine (such as joints) and fittings at regular
intervals even if they are not listed in the lubrication plan.

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды