Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 75

Страница: 75 / 130

BA 5001-6001 US – Edition 1.2 * 6001b330.fm

3-43

Operation

6001

The battery master switch is located under the engine cover. The battery master switch is
located behind the right-hand side maintenance flap on machines equipped with an
optional cab.

Important

Do not disconnect the battery while the engine is running.

Important

Power supply is interrupted directly after the battery, by means of a key.

• Disconnect the battery before working on the electric system.

Interrupting power supply:

☞

Turn key A of the battery master switch to position B and remove it.

Switching on power supply:

☞

Insert key A in the battery master switch.

☞

Turn the key down to the notched position C.

Fig. 68: Battery master switch (6001 with cab)

Fig. 68: Battery master switch (6001)

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды