Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 66

Страница: 66 / 130

3-34

BA 5001-6001 US – Edition 1.2 * 6001b330.fm

Operation

3.19 Front dump bucket operation

Important

Do not drive the machine with a raised dump bucket.

☞

Make sure the dump bucket is completely lowered before driving the
machine.

The working speed of the dump bucket is set with the bucket control lever and
the accelerator pedal.

NOTICE:

Lowering the dump body too rapidly and knocking it against the chassis

may cause machine damage

WARNING

Crushing hazard. Lowering the dump bucket rapidly may cause the machine to
tip over.

☞

Do not lower the dump bucket rapidly

When dumping into a pit:

• Always be certain the ground around the pit can support the weight of the machine

and the load.

• Always place the forward-reverse control in the neutral position.
• Always use a secondary means of braking such as a beam to chock the front wheels.

Fig. 57: Front dump bucket operation

Position

Lever

Function

☞

Lever pushed forward

➥

Dumps out the dump bucket

☞

Lever pulled backward

➥

Lowers the dump bucket

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды