Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 76

Страница: 76 / 130

3-44

BA 5001-6001 US – Edition 1.2 * 6001b330.fm

Operation

3.30 Engine cover (machines without cab)

Opening:

☞

Stop the machine.

☞

Let the engine cool down.

☞

Press buckle A of the engine cover downward and pull shackle

to the front.

☞

Pull the engine cover upward with handles

until the red safety prop

locks into place.

Closing:

☞

Press safety prop

to the rear.

☞

Press down the engine cover.

☞

Press buckle

forward and hitch shackle

into the hook at the same time.

☞

Press lock A to the rear.

Locking and unlocking:

The engine cover can be locked with an external lock in eyelet D.
Do not lock the engine cover during machine operation!
The emergency switch is located underneath the engine cover.

Fig. 69: Engine cover lock

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды