Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 56

Страница: 56 / 130

3-24

BA 5001-6001 US – Edition 1.2 * 6001b330.fm

Operation

3.11 Seat adjustment

CAUTION

Possible loss of machine control while adjusting the operator seat.

☞

Never change the seat position during machine operation or travel.

☞

Adjust the seat before operating the machine.

☞

– see

Before starting the engine on page

3-14

Weight adjustment

Important

Adjust the seat suspension correctly to ensure a high level of ride comfort.

To adjust to a higher weight:

☞

Turn the adjusting wheel to the right.

To adjust to a lower weight:

☞

Turn the adjusting wheel to the left.

The specified weight is indicated by the yellow pointer next to the adjusting wheel.

Horizontal adjustment

☞

Sit down on the operator seat.

☞

Pull lever 19 upward and at the same time.

☞

Move the operator seat forward or backward.

Backrest adjustment

☞

Pull lever

up and at the same time press against the backrest to move it to the

required position.

☞

Let lever

lock into place.

Fig. 40: Weight adjustment

70 kg

Fig. 41: Horizontal seat adjustment

Fig. 42: Backrest adjustment

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды