Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 88

Страница: 88 / 130

5-10

BA 5001-6001 US – Edition 1.2 * 6001b510.fm

Maintenance

Filling up engine oil

NOTICE:

Possible engine damage from too much oil or incorrect engine oil.

☞

Do not add engine oil above the MAX mark of oil dipstick 96/A.

☞

Use only the specified engine oil.

Environment

Use a suitable container to collect the engine oil as it drains and dispose of it in
an environmentally friendly manner!

Filling up engine oil

☞

Proceed as follows:

• Clean the area around oil filler cap

with a lint-free cloth.

• Open filler cap

• Raise oil dipstick

slightly to allow any trapped air to escape.

• Add engine oil.
• Wait about 3 minutes until all the oil has run into the oil sump.
• Check the oil level

– see

Checking the oil level

on page 5-9.

• Fill up if necessary and check the oil level again.
• Close filler cap

• Push oil dipstick

back in as far as possible.

• Completely remove all oil spills from the engine.

Fig. 77: Filling up engine oil (6001)

OIL

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды