Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 95

Страница: 95 / 130

BA 5001-6001 US – Edition 1.2 * 6001b520.fm

5-17

Maintenance

Retightening the V-belt

NOTICE:

Possible engine damage. Overtightening the V-belt may damage the V-

belt, the V-belt guide and the water pump bearing.

☞

Avoid contact of oil, grease or similar substances with the V-belt.

☞

Check V-belt tension—

see “

Checking V-belt tension on page

5-16

• Retighten as follows:

☞

Stop the engine.

☞

Fold the control lever base up.

☞

Remove the key and carry it with you.

☞

Disconnect the battery or the battery master switch.

☞

Let the engine cool down.

☞

Open the engine cover.

☞

Slacken fastening screws

of alternator

☞

Use a suitable tool to push the alternator in the direction of arrow

until reaching the

correct V-belt tension (fig. 83).

☞

Keep the alternator in this position, and at the same time retighten fastening
screws

☞

Check V-belt tension again and adjust it if necessary.

☞

Connect the battery or the battery master switch.

☞

Close the engine cover.

Fig. 83: Retightening the V-belt

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды