Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 49

Страница: 49 / 130

BA 5001-6001 US – Edition 1.2 * 6001b330.fm

3-17

Operation

Procedure

☞

Drive the jump-starting vehicle close enough to the machine so that the jump leads can
reach to connect the two batteries.

☞

Let the engine of the jump-starting vehicle run.

☞

First connect one end of the red jump lead (

) to the

terminal of the flat battery, then

connect the other end to the

terminal of the starting battery.

☞

Connect one end of the black jump lead (

–

) to the

–

terminal of the starting battery.

☞

Connect the other end of the black jump lead (

–

) onto a solid metal component fimly

mounted on the engine block or onto the engine block itself. Do not connect it to the
negative terminal of the flat battery, as otherwise explosive gas emerging from the
battery may ignite if sparks are formed!

☞

Start the engine of the machine with the flat battery.

Once the engine has started:

☞

With the engine running, disconnect both jump leads in exactly the reverse order (first
remove the

–

terminal, then the

terminal)—this prevents sparking in the vicinity of

the battery!

Fig. 29: Starting aid with jump leads

Flat battery

Starting battery

Содержание Dumper 5001



































































































































Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды

Wacker Neuson Dumper 5001, Руководство оператора

Результаты поиска

Содержание Dumper 5001

Отзывы:

Похожие инструкции для Dumper 5001

Бренды по названию

Популярные бренды