Wacker Neuson Dumper 5001 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 130

background image

BA 5001-6001 US – Edition 1.2 * 6001b110.fm

1-11

Introduction

Description

Hydraulic oil filler inlet. Use only specified hydraulic fluid.

– see chapter

Filling up hydraulic oil

on page 5-21

Location

On the filler inlet of the hydraulic oil tank

Description

Rotate the dump bucket support bracket from the stored position to the locked position,
supporting the dump bucket before entering the area under the dump bucket to perform an
inspection, maintenance, or repair to the machine.

Location

Near the maintenance strut

Description

Dump bucket control mode: dump and lower

Location

On the engine cover by the hand control

Description

Control identification for swiveling the dump bucket as viewed from the operator seat.

Location (5001, 6001S)

On the engine cover

Description

1:Attention! Remove starter key and read the Service Manual before servicing the
machine.
2:Hot surface! Do not touch. Keep a safe distance from the machine.
3:Cutting hazard. Cooling fan can cut when rotating. Stop engine before working on the
engine or cooling system.
4:Crushing hazard. Before performing maintenance work, let the safety strut lock into
place under the engine cover.

Location

On the engine cover

Description

Always fasten the lap belt if the rollbar is raised!
Do not use the seat belt when the ROPS bar is lowered to the stored position.

Location

On the engine cover

Fig. 17: Hydraulic oil label

Fig. 18: Label: maintenance strut

Fig. 19: Dump bucket control mode

Fig. 20: Swiveling the dump bucket

Fig. 21: Label: caution

Fig. 22: Seat belt application

«
...
17
18
19
20
21
...
»

Содержание Dumper 5001



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dumper 5001

Бренд: UFO Страницы: 16

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: Tar River Страницы: 61

Бренд: Tadano Страницы: 16

Бренд: Parker Страницы: 24

Бренд: Lumineux Страницы: 2

Бренд: Opvimus Страницы: 50

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

SonicShield I Micro

Бренд: CMS Marine Страницы: 15

Бренд: Dean Страницы: 2

neoBLUE LED Phototherapy Radiometer

Бренд: natus Страницы: 18

Бренд: Atlas Copco Страницы: 10

Бренд: Denon Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды